Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Liner & Rebuild for Kensington Homeowners
If your fireplace sends smoke back into the room, your liner has failed its one job: moving combustion gases up and out. In older Kensington homes, clay tile liners crack along the mortar joints, and a cracked liner lets carbon monoxide and heat reach the wood framing around the chimney. We handle the whole repair, from a stainless steel reline to a partial rebuild of the stack above the roofline, and our technicians have up to 9 years of experience with tile, cast-in-place and steel systems. Call (855) 974-3360. We answer 24/7, and fast dispatch from 7am to 7pm gets an evaluation scheduled, often the same day.
What Our Chimney Liner & Rebuild Service Includes
Every liner and rebuild job starts with a camera inspection, so the recommendation matches the actual condition of your flue. From there, we work through one of six paths, sometimes more than one on the same chimney.
Stainless Steel Liner
A stainless steel liner is a rigid or semi-rigid flue pipe that slides inside the existing chimney and gives the fireplace a smooth, sealed path for smoke and gases. You need one when the clay tiles are cracked, spalling or missing, or when a new appliance requires a correctly sized flue. We size the liner to the appliance and insulate it where the flue passes near combustible framing, which is where a lot of older homes get into trouble.
Flexible Liner
A flexible liner bends through offsets and turns that a rigid pipe can’t follow, and it’s the practical answer for the many chimneys in Kensington that were built with a jog in the flue. It’s the right choice when a straight run isn’t possible but the chimney is still structurally sound. We use DuraFlex flexible systems because they hold their shape through the bend without kinking, and we confirm the fit with a camera before and after installation.
Liner Replacement
Replacing a liner means pulling the failed clay tile or old steel pipe and installing a new one rated for the appliance you actually burn. This comes up when a previous liner was sized for a wood stove but the homeowner has since switched to a gas insert, or when an old liner has corroded through. We map the existing flue, size the replacement to the appliance, and document the whole swap with photos you keep.
Partial Rebuild
A partial rebuild addresses the damaged section of a chimney, usually the top few courses where water and freeze-thaw have loosened mortar and brick. You need it when the crown is failing, the top courses are spalling, or the flashing has pulled away and let water in. We rebuild the affected section, reset the crown and cap, and leave the sound lower portion alone instead of selling you a full tear-down you don’t need.
Full Chimney Rebuild
A full rebuild takes the chimney down to a sound base and puts it back up, which is the right call when the structure has leaned, separated from the house, or lost so much brick and mortar that patching won’t hold. This is heavy structural work with real safety stakes, and it belongs in trained hands, not a weekend project. We rebuild to current code, coordinate the liner installation into the new stack, and make sure the crown sheds water away from the flue.
Liner Repair
Liner repair covers smaller fixes: sealing cracks with a cast-in-place resurfacing system, reconnecting a disconnected section, or addressing a joint that has opened up. It’s worth considering when the liner is mostly intact but has isolated defects. HeatShield resurfacing is a good fit for that situation because it restores the flue from the inside without a full tear-out, and we tell you plainly when a repair will hold and when it won’t.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Liner & Rebuild
We install and service professional-grade liner systems, the same materials specified by certified chimney professionals: DuraFlex, HeatShield, Famco and Copperfield. Each behaves differently in the field. DuraFlex flexible systems work through tight offsets and turns; HeatShield is a cast-in-place resurfacing product we use on liners that just need their interior restored; Famco and Copperfield components come into play on cap, crown and structural work. Knowing where each one wears and where it’s the wrong tool matters as much as the brand name on the box.
Our technicians have up to 9 years of experience with these systems, so we can tell you which material fits your chimney’s actual condition rather than defaulting to whatever is easiest to install. Whether your chimney carries DuraFlex, HeatShield, Famco or Copperfield, or you’re starting from bare clay tile and no liner at all, we can help. We specify professional-grade materials because your chimney vents fire, and the liner is the part standing between combustion gases and the structure of your home.
Signs You Need Chimney Liner & Rebuild Right Now
Some liner problems announce themselves; others only show up on camera. These are the signs that mean it’s time to stop burning and get the chimney looked at.
- Smoke rolling back into the room. A liner that has cracked, separated or is the wrong size for the appliance won’t pull smoke up and out, so it spills into the living space instead. Backdrafting also means combustion gases are coming inside, which is a carbon monoxide concern, not just a smell.
- White staining or crumbling on the exterior brick. Efflorescence and spalling brick on the outside often trace back to water getting in at the crown or flashing, and a deteriorating exterior usually means the flue interior is degrading too. Catching it early keeps the repair in partial-rebuild territory instead of a full rebuild.
- A visible crack or gap in the clay tile. If you can see broken tile joints from the firebox, the liner has lost its seal and heat can reach the framing. This is one to get evaluated before the next fire, not after.
- Debris or flakes falling into the firebox. Bits of tile or mortar dropping down mean the flue lining is breaking up from the inside. Those pieces also narrow the flue and make the chimney draft worse over time.
- A chimney that has pulled away from the house or is leaning. Structural separation or a lean is a rebuild conversation, and it’s not something to schedule around. Stop using the fireplace and have the stack evaluated by trained technicians before anything else.
Our Chimney Liner & Rebuild Process – Step by Step
- 1
Camera inspection. We run a video camera down the flue and look at every joint, the smoke chamber, the damper and the crown. You see the footage, so the recommendation is grounded in what the camera found, not a guess.
- 2
Written estimate and material plan. We lay out the options in writing, from a resurfacing repair to a full reline or rebuild, with the price for each. The written estimate sets the final price, and the flat price is agreed before any work is booked.
- 3
Site protection and tear-out. Floors and furnishings get covered, and we remove the failed liner, damaged brick or old components, keeping the work area contained. If the job is a partial rebuild, we isolate the sound section from the work zone.
- 4
Installation. We install the liner or rebuild the stack using the material matched to your chimney, insulate the flue where code calls for it, and reset the crown and cap. Every stage is checked against the appliance’s sizing and the local code requirements for venting.
- 5
Final camera pass and photo report. We run the camera again to confirm the finished flue, test the draft, and hand you the photo report of the completed work. You keep the record of what was done and how it looked when we finished.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Kensington?
Chimney liner and rebuild work in Kensington is priced per job, and the written estimate is what sets the final number. The ranges below reflect typical scenarios, not quotes.
| Service | Typical Estimated Range | What Drives It |
|---|---|---|
| Liner repair / resurfacing | $600 – $1,400 | Extent of interior damage, whether resurfacing alone will hold |
| Stainless or flexible reline | $1,800 – $4,500 | Flue height, liner diameter, insulation, appliance type |
| Liner replacement | $2,000 – $5,000 | Removing the old liner, offsets in the flue, new sizing |
| Partial rebuild | $2,500 – $6,000 | Number of courses replaced, crown and flashing condition |
| Full chimney rebuild | $6,000 – $15,000+ | Height, access, structural separation, liner included in the new stack |
What pushes a job toward the higher end: a tall stack that needs more liner material, a flue with multiple offsets, a chimney that has to be rebuilt down to a sound base, or an appliance change that requires resizing the whole vent. The way to avoid overpaying is to insist on camera evidence before anyone quotes a liner or a rebuild. We don’t recommend thousands of dollars of masonry or liner work you can’t verify; you see the footage, and we tell you plainly when a repair can safely wait.
A free estimate includes the camera inspection, the written breakdown of options and the photo report, with no obligation. Liner and rebuild work should meet NFPA 211 and local code requirements, and our estimates account for that so the repair holds up, not just passes a glance.
Chimney Liner & Rebuild Near Kensington – Our Service Area
We schedule liner and rebuild work across Kensington and the surrounding communities, including Port Richmond, Fishtown, Southwest Philadelphia, Eastwick, Upper Darby, East Lansdowne, Yeadon, Darby, Lansdowne, Ardmore and Lower Merion. If you’re outside that list, call and we’ll confirm coverage. Rebuilds take longer to schedule than a reline because of the structural work, so the sooner you book the evaluation, the sooner it’s on the calendar. Read more about our chimney liner & rebuild capabilities and what the process involves.
Serving Kensington, PA – Our Local Coverage Area
We serve Kensington and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Liner & Rebuild in Kensington
Chimney liner and rebuild work is the repair or replacement of the flue lining and, where needed, the structural brick and mortar of the chimney itself. The liner is the pipe that carries smoke and gases up and out; a rebuild restores the stack when water damage, freeze-thaw or age has compromised the brick. Together they keep the chimney venting safely and up to code. Call (855) 974-3360 for a free estimate if you’re unsure which your chimney needs.
A reline is usually done in a single visit, while a partial rebuild takes a few days and a full rebuild runs longer depending on height and access. The camera inspection and estimate happen first, so the schedule is set from the actual scope, not a guess. We’ll give you the expected timeline in writing with the estimate. Call (855) 974-3360 to get the evaluation booked.
Liner repair or resurfacing typically runs $600 – $1,400, a full reline $1,800 – $4,500, and rebuilds from $2,500 into five figures depending on scope. The written estimate sets the final price, and the free estimate includes the camera inspection and photo report. Nothing is recommended without evidence you can see. Call (855) 974-3360 for an exact quote; estimates are free.
Yes, we install and service DuraFlex flexible liners and HeatShield cast-in-place resurfacing, along with Famco and Copperfield components on cap, crown and structural work. Knowing which system fits your chimney’s condition is the point, not selling the same material to every homeowner. If your chimney already carries one of these brands, we’ll evaluate it and tell you whether it can be repaired or needs replacing. Call (855) 974-3360 for an assessment.
Same-day scheduling is often possible for an evaluation, though a rebuild itself is booked by scope. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, gets a technician to your door. We’re closed Saturday, and a call outside dispatch hours is booked into the next opening. Call (855) 974-3360 to schedule.
We stand behind the work with a satisfaction guarantee, and the materials come with the manufacturer’s warranty for the system installed. The photo report documents the finished job, so if anything needs a second look you have the record. The specifics are laid out in your written estimate. Call (855) 974-3360 with questions about coverage.
Clear access to the fireplace and the path to the chimney, and move anything breakable away from the work area. If the chimney is on an exterior wall, make sure the technicians can reach it safely from the ground or roof access. We handle protection of floors and furnishings. Call (855) 974-3360 if you’re unsure what to move.
Schedule Your Chimney Liner & Rebuild Service in Kensington Today
A failed liner or a leaning stack is the kind of thing that’s cheaper to fix now than after a season of use. Call (855) 974-3360 for a free estimate on a stainless or flexible reline, a liner replacement, or a partial or full rebuild. You’ll see the camera footage, get a written price, and know exactly what the work involves before anything is booked. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. One crew, every layer of your chimney, built to last. Start with a sweep if it’s been a while: our chimney sweep in Kensington is the natural first step before liner work.
Written by the team at Chimney Sweep Kensington.