Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Kensington Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning, inspection and repair service in Kensington, PA. Our technicians know Gelco stainless multi-flue caps, top-mount dampers and clay flue tile assemblies from the inside out, so we can tell whether a smoke-back or draft problem is a cleaning job, a worn gasket or failing flue tile behind the cap. We are an independent service provider, not affiliated with, authorized by or endorsed by Gelco, and that independence means we recommend repair or replacement based on what your chimney actually needs.
Kensington’s rowhouse chimneys make that judgment matter. Most of the housing stock here is 19th- and early-20th-century attached brick, and cleaning work happens from rooftops where ladder placement and neighboring rooflines set the terms of the job, not a freestanding house with clear ground access. You can reach us at (855) 974-3360. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Our technicians have up to 9 years of experience, and our work runs from creosote removal and cap replacement to a full Level 2 inspection when the flue needs a closer look. Call (855) 974-3360 for a free estimate.
Why Trust Chimney Sweep Kensington for Your Gelco Chimney Cleaning?
Our technicians have handled Gelco caps and dampers often enough that the brand’s construction details are familiar territory: how the flue tile openings are laid out under a multi-flue cap, the geometry of a top-mount damper frame, and the mounting patterns that hold a cap down against wind and weather. That familiarity means we diagnose from what we see on your chimney, not from a generic script.
We use quality parts that fit Gelco equipment. Where a like-for-like match matters, we lean on OEM Gelco components; where a quality aftermarket stainless or masonry piece performs equal to or better than the original, we’ll say so and explain why. Neither choice is automatic. It depends on your chimney’s condition, the age of what’s there and what you plan to do with the fireplace.
Warranty-safe practice runs through every job. We don’t drill, cut or force components in ways that compromise the assembly, and we document what we find with photos before and after so you have a record. We’re an independent shop, so our loyalty sits with your chimney, not with a brand’s sales targets. If a Gelco cap can be cleaned and re-gasketed rather than replaced, that’s what we’ll tell you.
Kensington homeowners on these blocks tend to know their neighbors’ chimneys almost as well as their own: on many blocks the flues sit close enough that one roof setup covers more than one house. That shared roofline reality shapes how we schedule and set up work here. Call (855) 974-3360 for a free estimate.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Kensington
Most Gelco service calls in Kensington come down to one of five failure patterns. Matching the symptom to the cause is the whole job.
- Corroded or seized cap mounting bolts. Stainless multi-flue caps sit in weather year after year, and the bolts that hold them down corrode and seize. Once they’re frozen, the cap no longer seals tight to the flue tops, and rain, squirrels and birds find the gap. We free or replace the hardware and reseat the cap so it seals again.
- Top-mount damper gaskets and linkage wearing out. A top-mount damper depends on a gasket and a linkage to close fully. When the gasket hardens or the linkage loosens, the damper sticks partway open. The fireplace feels drafty, cold air moves down the flue, and heat escapes up it. Cleaning won’t fix this; re-gasketing or replacing the assembly will.
- Cracked or spalled clay flue tile joints. Older Gelco clay-lined flues develop cracks and spalled joints as masonry moves with freeze-thaw cycles. Creosote and moisture work into those gaps and start degrading the surrounding brick. This is the failure that matters most, because it’s hidden behind the cap and the crown until an inspection finds it.
- Clogged cap screens and spark arrestors. Soot and creosote glaze pack into the screen mesh, cutting draft and pushing smoke back into the room. A clogged screen and a dirty flue feel the same to a homeowner; brushwork and screen cleaning usually solve both at once.
- Glazed creosote in a clay-lined flue. Cool flue temperatures and restricted draft let creosote bake into a hard glaze that ordinary brushing won’t remove. This is a fire-risk condition, not a cosmetic one, and it needs proper removal before the fireplace is used again.
Philadelphia’s freeze-thaw winters and humid summers speed up masonry spalling and crown cracking on exposed rowhouse chimneys, which is why so many Kensington blocks have cap and flue problems hiding in plain sight. Autumn is the busiest time for cleaning and inspection before heating systems fire up. If you’re not sure which of these you’re looking at, a Level 2 inspection settles it. Call (855) 974-3360 for a free estimate.
Gelco Parts & Our Repair-vs-Replace Approach
Choosing parts starts with matching the component to the chimney, not the other way around. We use OEM Gelco caps, damper assemblies and trim when a like-for-like match matters, and quality aftermarket stainless and masonry components where they perform equal to or better than the original. We don’t claim to stock genuine Gelco parts: we source what fits and tell you what you’re getting.
The repair-or-replace call follows a simple rule. If a Gelco cap or damper is structurally sound, cleaning and re-gasketing beats replacement every time. If the flue tile or crown behind it is failing, no amount of part-swapping fixes the chimney. We show you the evidence before recommending either path, so you can see the cracked joint or the worn gasket yourself.
That approach is built for durability, not for passing a quick look. Call (855) 974-3360 for a free estimate.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We start at the cap and work down: cap mounting, screen condition, damper operation, then the flue tiles and crown. A Level 2 inspection with camera work happens when the symptom points past the cap. We photograph what we find.
- 2
Repair or install. Once the cause is clear, we clean and re-gasket a sound cap or damper, or install a properly sized replacement. Creosote removal and cap replacement often run on the same visit.
- 3
Test. We check the damper closes fully, confirm the cap seals and the screen is clear, and verify draft before we call the job done.
- 4
Warranty and record. You get before-and-after photos and a clear note of what was serviced, which protects you if a warranty question ever comes up.
If you’re not sure which step your chimney needs, call (855) 974-3360 for a free estimate.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Kensington
We service and install Gelco stainless steel multi-flue chimney caps, top-mount damper assemblies, clay flue tile liners and crowns, and fireplace insert surrounds and glass door sets. That covers the full line of Gelco components a Kensington rowhouse chimney is likely to have, from the cap on the roof down to the firebox surround at the hearth. Whether it’s a seized cap that needs freeing, a damper that needs re-gasketing, or clay tile that needs inspection, we handle it. Call (855) 974-3360 for a free estimate.
We Also Service These Brands
Gelco work is one part of what we do. We also service and install DuraFlex and HeatShield liner systems, along with Olympia Chimney, Famco and Copperfield components. That multi-brand reach means we can match a solution to your chimney’s condition instead of steering you toward whatever we happen to carry. Call (855) 974-3360 for a free estimate.
FAQs – Gelco Chimney Cleaning Service in Kensington
No. We are an independent Gelco service provider, not affiliated with, authorized by or endorsed by Gelco. We service and install Gelco equipment using quality parts that fit, and our independence lets us recommend repair or replacement based on your chimney’s real condition. Call (855) 974-3360 for a free estimate.
Yes. We use OEM Gelco caps, damper assemblies and trim when a like-for-like match matters, and quality aftermarket stainless and masonry components where they perform equal to or better than the original. Call (855) 974-3360 for a free estimate.
Most Gelco cap and damper service calls finish in a single visit. Symptom matching to cause takes the most time: freeing a seized cap, re-gasketing a damper or clearing a clogged screen is usually quick, while a Level 2 inspection with camera work takes longer. We confirm timing in your written estimate.
We cover stainless multi-flue chimney caps, top-mount dampers, clay flue tile liners and crowns, and fireplace insert surrounds and glass door sets. Call (855) 974-3360 for a free estimate.
Our work is done in ways that protect your Gelco assembly. We don’t force, drill or cut components in ways that compromise them, and we documented what we serviced with before-and-after photos. We’re independent and can’t speak to Gelco’s warranty terms directly, so ask us to note the parts used on your record and check with Gelco on coverage.
Gelco chimney cleaning is priced per job by a written estimate after we inspect your chimney. A simple sweep with a cap check is on the lower end; creosote glaze removal, a re-gasket or a replacement cap adds cost. The written estimate sets the final price, and the estimate is free. Call (855) 974-3360 for an exact quote.
Yes, in most cases. If the cap is structurally sound, cleaning it and re-gasketing or freeing the hardware beats replacement. We replace only when the cap is corroded through or the flue tiles behind it are failing. Call (855) 974-3360 for a free estimate.
Usually not. A sticking top-mount damper points to a worn gasket or loosened linkage more often than soot. Cleaning helps draft; re-gasketing or replacing the assembly fixes the seal. Call (855) 974-3360 for a free estimate.
Yes. A Level 2 inspection needs access to the flue interior, so the cap comes off first. That’s also the moment to check cap bolts and screen condition while it’s down. Call (855) 974-3360 for a free estimate.
Cool flue temperatures and restricted draft let creosote bake into a hard glaze on the clay tile. A clogged cap screen makes it worse by cutting draft further. Glazed creosote is a fire-risk condition that needs proper removal, not a quick brush. Call (855) 974-3360 for a free estimate.
Yes. We match the component to the flue, not the label. A quality stainless cap or damper from another maker works fine if it sizes and seals correctly. Call (855) 974-3360 for a free estimate.
Book Your Gelco Service in Kensington, PA
Whether it’s a clogged Gelco cap screen, a damper that won’t seal or clay tile that needs inspection, we’ll find the cause and tell you plainly what it needs. Call (855) 974-3360 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Kensington.