Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Kensington Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning service in Kensington for homeowners whose chimneys are lined with a flexible stainless steel relining system. What sets our DuraFlex work apart is that we service the whole assembly, not just the flue: the liner wall, the insulation wrap, the tee, the top plate and the appliance connector that ties it all together. We’re an independent DuraFlex service provider, not affiliated with or authorized by the manufacturer, and that independence is exactly why our recommendations hold up. Our technicians have up to 9 years of experience. Call (855) 974-3360. We answer 24/7, with fast dispatch from 7am to 7pm.
Why Trust Chimney Sweep Kensington for Your DuraFlex Chimney Cleaning?
DuraFlex liners are one of the most common stainless relining systems in older Pennsylvania coal-town housing stock, and Kensington’s rowhouse blocks are full of them. An independent sweep who works on these assemblies regularly learns them from the inside out: how the insulation wrap sits against the outer wall, how a tee seats into the base, how a top plate terminates at the crown, and how the appliance connector ties back into the firebox. That hands-on familiarity, not a manufacturer endorsement, is what makes a diagnosis trustworthy.
We use quality parts that fit DuraFlex equipment. When a component needs replacing, we match the correct insulation wrap, tee, top plate and appliance adapter to the assembly so its listing stays intact. Service is warranty-safe: we clean and re-terminate in a way that respects how the system was built, and we tell you plainly when a liner is sound enough to keep and when it isn’t. We’re independent, we’re careful, and we explain what we find.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in Kensington
A DuraFlex liner is a flexible stainless steel flue wrapped in insulation, and its flexibility is both its strength and its weak point. Here’s what we find most often on Kensington chimneys.
- Degraded or torn insulation wrap. The wrap is what keeps creosote and condensate off the outer stainless wall and holds the assembly’s UL listing together. When it tears during a rough cleaning or wears thin over years of freeze-thaw cycling, moisture reaches the metal and the listing breaks. On exposed rowhouse chimneys, where Philadelphia winters flex the masonry above, wrap integrity is the first thing we check.
- Creosote glazing on the corrugated inner wall. Flexible liners have a corrugated interior where a brush can skip over glazed creosote, especially on low-draft appliances and inserts. That glazing hardens and builds until draft suffers and the flue becomes a fire risk. Corrugated walls need a brush technique that reaches into the ridges, not a quick pass.
- Separated or crushed sections at forced offsets. When a liner was routed around a smoke shelf or damper frame, the installer had to force it. Over time a crushed or creased section collects soot and restricts flow, and a separated joint lets creosote leak behind the liner. These show up clearly on camera during a Level 2 inspection.
- Loose or corroded top plates and tee caps. The top plate and tee cap are the water seals. When they loosen, corrode or were never seated right, rain runs down the outside of the liner and soot works back into the firebox or chase. It’s one of the most common reasons a DuraFlex-equipped chimney smells smoky after a storm.
- Failing appliance connectors. The connection between the liner and the appliance is a joint that flexes with heat cycles. A loose or corroded connector lets exhaust and soot escape into the chimney chase instead of up the flue. We check every joint, not just the visible run.
On many Kensington blocks the chimneys stand so close that a single roof setup gives us access to more than one flue, which is good news for inspection. The hard part is access: most work here happens from the roof of an attached rowhouse, where ladder placement and neighboring rooftops dictate the job, not a freestanding house with clear ground access. That reality changes how we plan a cleaning and how carefully we handle the wrap and top plate while we’re up there.
DuraFlex Parts & Our Repair-vs-Replace Approach
DuraFlex liners depend on matching parts: the correct insulation wrap, the tee, the top plate and the appliance adapter. Aftermarket substitutes that don’t fit the assembly compromise its listing, so we specify quality parts that fit the system rather than improvising. We don’t stock or sell genuine DuraFlex parts and we’re not a dealer; what we do is repair, install and service DuraFlex equipment with parts built for it.
Our repair-or-replace call comes down to condition. If a liner is sound (the wall intact, the wrap whole, the joints tight), cleaning and re-terminating is the honest answer, and we’ll say so. If the wrap is torn, a section is crushed, or the liner was installed uninsulated, a partial patch rarely holds and a full reline is the responsible recommendation. We show you the camera footage so you can see the difference yourself, and we tell you plainly when work can safely wait. Call (855) 974-3360 for a free estimate.
Our DuraFlex Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection, running a camera the full length of the liner and checking the insulation wrap, every joint, the offset points, the top plate and the tee. On a Kensington rowhouse that means planning the roof access first, since ladder placement on attached chimneys takes care.
- 2
Cleaning or repair. We remove creosote with a technique suited to the corrugated wall, then handle whatever the inspection found: re-seating or replacing the top plate and tee cap, correcting an appliance connector, or recommending a reline where the wall is compromised.
- 3
Test. We verify draft and check the seals hold, watching for the smoke-back and water intrusion that a failed top plate or torn wrap causes.
- 4
Warranty-safe close-out. We leave you with a clear photo report of what we found and what we did, documented so the assembly’s integrity is preserved and any manufacturer warranty stays intact.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Kensington
We work across the DuraFlex system as it’s actually built: smooth-wall and flexible stainless relining kits, the insulation wrap and blanket kits in both half-inch and quarter-inch profiles, and the tee and top-plate termination components that finish the job. We install and service these on Kensington chimneys of every configuration, from a straightforward single-flue run to a multi-flue rowhouse chimney with original brick and later conversions. We also handle the Level 2 inspections, creosote removal and cap replacement that go with keeping a DuraFlex assembly healthy. We don’t claim to stock these products; we specify and fit the right ones for your chimney’s condition.
We Also Service These Brands
DuraFlex is one of several professional-grade brands we work with. We also service HeatShield, Gelco, Olympia Chimney, Famco and Copperfield. That range matters in Kensington, where liners, caps and flue configurations vary widely from block to block: we recommend the right material for your chimney’s condition rather than steering every job toward one brand. One crew, every layer of your chimney system, from the cap to the firebox floor.
FAQs – DuraFlex Chimney Cleaning Service in Kensington
No. We’re an independent DuraFlex service provider, not affiliated with, authorized by, or endorsed by the manufacturer. Our expertise comes from working on these assemblies regularly, not from any factory certification, and we tell you that straight so you can judge our recommendations on the evidence we show you.
Yes, when it’s done with a technique suited to the flexible corrugated wall. A flexible liner’s ridges hold glazed creosote that a fast pass skips, so we use a brush approach that reaches into the corrugation without tearing the insulation wrap or forcing the wall. Rough cleaning is what damages wraps, and we’re careful about it. Call (855) 974-3360 for an exact quote; estimates are free.
Water usually gets in because the top plate seal has failed, loosened or corroded, or because the cap above it is compromised. The top plate is the water seal at the crown, and when it isn’t seated right, rain runs down the outside of the liner and shows up as a smoky smell and damp soot in the firebox. We inspect and re-seat or replace it as part of a cleaning visit.
You can’t tell from the firebox, which is why a camera inspection matters. The wrap is doing its job when it’s whole and continuous along the liner; it’s failed when it’s torn, thin or missing at an offset. A Level 2 inspection shows the wrap on camera so you can see its condition yourself rather than taking our word for it.
DuraFlex cleaning is priced per job by a written estimate after we’ve inspected the liner, the wrap and the termination, since a single-flue rowhouse run and a multi-flue chimney with a failed top plate are different jobs. The estimate is free and the written estimate sets the final price. Call (855) 974-3360 for an exact quote; estimates are free.
A small crease is often fine, but a crushed section at a forced offset is not, because it collects soot, restricts draft and can hide a tear in the wrap behind it. The only way to know which you have is to see it on camera. We’ll show you and tell you plainly whether it can stay or needs a reline. Call (855) 974-3360 for an exact quote; estimates are free.
Book Your DuraFlex Service in Kensington, PA
If your Kensington chimney has a DuraFlex liner and you want it cleaned and checked properly, call (855) 974-3360 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect the whole assembly, show you what we find, and tell you straight what it needs.
Written by the team at Chimney Sweep Kensington.